Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Abatement Technologies Coil Cleaning: The Fort Lauderdale Owner’s Guide
If your Abatement Technologies coil cleaning system isn’t pulling the way it used to, we stock the replacement parts and do the work here in Fort Lauderdale. A typical coil cleaning service on Abatement Technologies equipment runs $185 to $390 depending on the unit and how far gone the coil is. Most owners call us after they notice the suction dropping off or hear the motor laboring harder than it did last spring.
Here’s what usually happens: the coil loads up with a paste of dust, salt air residue, and the kind of humidity-driven grime Fort Lauderdale produces year-round. The motor keeps running, but the airflow chokes down until the machine can’t do its job. If you’re reading this, you’ve probably already noticed something’s off.
Which Abatement Technologies Models This Applies To
Abatement Technologies makes negative-air machines and coil cleaning units in a few series: the HEPA-AIRE line, the Predator series, and their commercial portable units. The coil cleaning setup differs by model, mostly in access panel placement and coil thickness. Before you order anything, check the data plate on the back or side of the unit. You want the model number and the serial prefix. That tells us whether you’re running a first-generation coil tray or the newer washable-mesh version, and the two don’t interchange.
Here’s the gotcha we see often: the Predator series uses a stacked coil with tighter fin spacing than the HEPA-AIRE units. If you swap in a generic aftermarket coil meant for the wrong series, it’ll fit the housing but starve the airflow. We match OEM Abatement Technologies parts when the unit is under warranty or when the customer wants factory spec. For older units out of warranty, quality aftermarket coils from brands like Guardsman do the job at a better price, but we tell you which one you’re getting before we touch anything. That’s the whole point of a written price.
Styles & brands we work with
Signs Your Abatement Technologies Coil Cleaning Is Failing
- Suction drops off mid-job. The coil is loading up with debris faster than the unit can shed it. That’s usually the first sign, and it gets worse through the job, not better.
- The motor smells hot. A plugged coil makes the motor work against a wall of resistance. In Fort Lauderdale’s heat, that motor is already running near its limit, and a dirty coil pushes it past.
- You see visible buildup on the fins. If you can see a gray paste on the coil face, airflow is already down more than you’d guess. This is the point where cleaning beats replacing.
- The drain pan fills faster than it should. Condensate that can’t shed properly pools in the pan, and in Florida humidity, that pan overflows quick.
- The unit trips its thermal overload. Abatement units have a safety cutoff. When the coil is so packed the motor overheats, the cutoff trips and the machine shuts down entirely. That’s the unit telling you it’s done until the coil gets serviced.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Fort Lauderdale, coil cleaning on Abatement Technologies equipment runs $185 to $390 installed. The range comes down to coil condition and access. A unit with a decade of hard use and a coil that needs removal and a chemical soak lands at the top. A newer unit that just needs a proper fin-combing and wash lands lower.
The price includes the coil service or replacement part, labor, and a written receipt that shows exactly what was done. If we replace a coil, you get the part number and the warranty terms in writing. Every job we do is covered by our 365-Day Done Right Promise: if the work fails within a year, we come back and make it right at no charge, including a free second visit. No per-vent pricing, no bait number that balloons when the work starts. The price we write down is the price you pay.
DIY or Call Us?
You can safely check a few things before you call: look at the coil face with a flashlight, check that the drain line isn’t kinked, and make sure the filter upstream isn’t collapsed. That’s where a homeowner should stop. Pulling the coil out of an Abatement unit means disconnecting the condensate line and working around the motor housing, and if you bend a fin or crack the drain barb, you’ve turned a $185 cleaning into a $400 replacement.
These units move air under pressure, and the coil is part of that pressure system. If you’re not sure, call us at (754) 354-3644. We’ll tell you over the phone whether it sounds like a clean-and-go or something bigger, and the estimate is free.
FAQs
In Fort Lauderdale’s salt air and humidity, an Abatement coil typically lasts 5 to 8 years before it needs replacement, assuming it gets regular cleaning. Units run near the coast or in buildings with heavy foot traffic trend toward the short end of that range because the air carries more moisture and particulate. We also mention Lennox, Trane, and Carrier parts on request for other units in your building.
A coil with bent fins or surface buildup can be cleaned and combed back to working condition most of the time. If the coil has corrosion pinholes from salt exposure or the internal channels are packed solid, replacement is the honest call. We’ll show you the coil and explain what we’re seeing before we recommend either route.
A standard Abatement coil cleaning takes about an hour to an hour and a half on site, including the fin combing and drain check. Full coil replacement runs two to three hours depending on access. We give you a written time window and a written price before work starts.
We keep common Abatement coil assemblies and aftermarket equivalents on the truck for most HEPA-AIRE and Predator series units. If your unit is an older or less common configuration, we order the part and have it in hand within a few business days. Call (754) 354-3644 with your model number and we’ll tell you what’s available right now.
Roy Castellanos has been doing HVAC and air duct work across South Florida for the better part of two decades, and he’ll tell you what your Abatement unit actually needs, not what adds the most to an invoice. Clean ducts move air. Everything else is just noise.
If your Abatement Technologies coil isn’t pulling air the way it should, call (754) 354-3644 for a free estimate. We’ll give you a written price before any work starts, and every job is backed by the 365-Day Done Right Promise. Fort Lauderdale’s humidity doesn’t let up, and neither should your equipment.
Written by Roy Castellanos, Owner, Hollis Air Duct Fort Lauderdale at Hollis Air Duct Fort Lauderdale, serving Fort Lauderdale and nearby areas.